|
Special Features
& Advantages
Space
It requires very small space, does not
require foundation or pump house
Investment
Cost
Due to compact and sturdy design, the
initial investment s low.
Installation
& Maintenance Cost
The
installation cost is very low, can be installed in difficult site in
narrow and slanting borewells. Due to proper selection of material and
due to high accuracy maintained during production maintenance cost is
very low. The operation of pump is noiseless.
Efficiency
Due to efficient design pump gives
higher output at lower power consumption.
The
Motor
- Motors are squirrel cage type totally enclosed,
wet type induction motor suitable for Single Phase, 230V / 3 Phase, 415
volts, 50 c/s a.c. supply, filled with pure drnking water
- Dual seals and sand guard are provided for
protection and to avoid contamination of outside borewell water
- Stator made of Stainless Steel pipe
- Stator & Rotors are impregnated with varnish
under vacuum and baked-under controlled temperature to avoid rusting in
water
- Stainless steel sleeves are shrink fitted at
bearing locations on rotor shaft and ground to closer tolerance for
smooth running
- Winding wire is made from water resistance P.V.C.
Coated / Poly coated copper wire
- Rotor assembly is dynamically balanced for
vibration free operation
- Rotor bars are of electrolytic grade copper
- All the bush bearings are water lubricated
- Thrust bearing assembly is fitted with tilted
pads resting on S.S. Balls and supported by locating pin to take the
higher axial load
- The revolving thrust plate is made from S.S.
& fitted with teflon securely fixed to the S.S. Plate
- Rubber diaphragm is provided at the base of the
motor to equalise pressure caused by variation in temperature during
operation
- Lead cables are protected with rubber gromets
- The motor is manufactured as epr IS 9283 / 1995
The Pump
- It is vertical multstage centrifugal pump with
either radial flow or mixed flow type Stainless Steel impeller
- Impellers are dynamically balanced. All the
stationary parts are closed grained graded CI with smooth profiles
without any determental defects
- All the Bearing Bush are self water lubricated
type
- The Pumpshaft Sleeves & Coupling are
manufactured from Stainless Steel
- Impeller & sleeves are securely fixed on S.S.
Shaft with S.S. Key
- The bowls are locked by bolting to avail high
Concentric accuracy and better reliability
- A stream lined non return valve provided to
prevent reverse rotation of pump assembly while switched off
- S.S. Suction strainer is provided to avoid entry
of suspended material in water
- To protect cable from being wearing out during
installation, cable guards are provided all along the pump body
The pump is manufactured as per IS: 8034
/ 2002.
Application:
-
Agriculture
- Tubewell Irrigation
- Openwell Irrigation
- Drip Irrigation / Sprinkler Irrigation
- River / Canal
Public Utilies
- Service Water Supply
- Fire Fighting Services
- Process & Cooling Water Circulation
- Booster Application
- Raw & Treated WAter SErvices
- Mining & Construction Sites
- Ornamental Like Fountains.
Range
Borewell
Dia.
|
Model
|
Head
Meters
|
Capacity
Lmp
|
HP
|
Supply
|
80 mm
|
JT Series
|
8-100
|
20-65 Lpm
|
0.5 to 1.25
|
Single Phase
|
100 mm
|
JA Series
|
10-200
|
20-300 Lpm |
0.5 to 3.00
1.0 to 7.50
|
Single Phase
Three Phase
|
125 mm
|
JF Series
|
10-200
|
40-550 Lpm |
3.0 to 10.00
|
Three Phase
|
150 mm
|
JS Series
|
15-250
|
80-1300 Lpm |
3.0 to 30.00
|
Three Phase
|
200 mm
|
JC Series
|
10-200
|
200-2200 Lpm |
5.0 to 60.00
|
Three Phase
|
250 mm
|
JO Series
|
10-150
|
1000-3500 Lpm |
10 to 100.00
|
Three Phase
|
Mono Set Pumps: -
Features
- The pump and motor being single unit, no
alignment, coupling is required
- The motor is wet type, water cooled and water
lubrcated type, available for 3 phase 415V and single phase 230V A.C.
Supply
- The motor s wound with PVC coated / Poly coated
wire of reputed make
- Stators and Rotors are manufactured with high
quality silicon stamping to reduce the losses and thereby increasing
efficiency of motor.
- Stators and Rotors are mpregnated with varnish
under vacuum and baked under controlled temperature to get hard finish
- All rotating parts like impellers and rotors are
dynamically balanced
- It can withstand wide variation of supply voltage
- Totally submerged in water, no priming required
- No pump house required, initial investment is low
- High overall efficiency results in lower power
bills
- Pollution free - no contimination of oil/grease
- All C.I. Parts are as per S - 210 FG 200.
Applicaton:
- Domestc water supply
- For lifting water from underground tank to
overhead tank in flats, housing complexes high rse buildings.
- Agriculture: For
open well application, where water level s not steady
- Industries: For
water crculating system, storage tank filling, Gardens, Hosptals,
Garage etc.
Single Phase 230
V, 50 HZ
A.C. Supply
|
0.5 HP to 3.0 HP
|
35 lpm to 500 lpm
|
Three Phase 415
V, 50 HZ
A.C. Supply
|
1.0 HP to 30 HP
|
200 lpm to 2000
lpm
3 m - 50 m
|
- These pumpsets are manufactured as per IS:
14220 / 1994
- Due to continuous R & D, the design and
features are subject to be changed without prior intimation.
|
|
